Change or rekey · Oshawa
Lock Replacement & Upgrade
Every morning the front door key needs the same little dance: push in, lift, wiggle, turn.
In plain words
A keypad or smart lock is a lock replacement with a few extra steps, and it suits households where keys circulate widely. The locksmith fits the new deadbolt to the existing bore, checks that the bolt throws freely so the motor is never straining against a misaligned strike, sets up user codes and any phone pairing, and shows you the mechanical override and the battery warning. Because these locks still rely on a bolt and a strike, the same attention goes into the frame as for any deadbolt. You gain convenience without giving up the mechanical basics that make a door hard to force.
How the visit goesThe keys the seller handed over came in a sandwich bag: six unlabelled copies for two locks of different makes from different decades. You have no idea how many more copies exist or who is holding them.
Lock Replacement & Upgrade
How the visit goes
How the old lock behaves in use
The locksmith works the existing hardware the way you do every day and watches for the tell-tale signs. A key that must be lifted or wiggled points to worn pins or a worn key. A knob that turns too far, or a lever that droops, suggests a tired spindle or spring. A latch that stays retracted, or a bolt that stops short, can be internal wear or something outside the lock altogether. Doing this with the door open first, then closed, separates faults inside the mechanism from faults in the fit of the door, and that distinction decides whether new hardware is the answer or part of the answer.
Fitting the latch or bolt to the door
Most modern latches and bolts adjust between the two common backsets, so the unit is set to the measured figure and slid into the edge bore. A spring latch goes in with its bevel facing the strike, while a deadbolt is oriented the way its markings or instructions call for, not by that bevel rule. The faceplate should sit flush in its mortise; where the old cut-out differs in shape or size, the mortise is trimmed with a sharp chisel, or a round drive-in collar is used where the door was prepared that way. The bolt is checked to travel freely before anything else goes on, since a bolt that binds in the door will bind under the key too.
The rental paperwork, quietly sorted
If the door belongs to a rental unit, the visit finishes with the keys in the right hands. When a landlord orders the change, giving the tenant a full set of new keys is standard practice. When a tenant orders it with the landlord's consent, a key for the landlord is cut alongside the household's and the consent is noted. The locksmith can leave a short written record of the hardware fitted and the keys issued for the property file, so both sides know what is on the door and nobody is surprised at the next inspection or move-out.
Lock Replacement & Upgrade
In the van
Knob or lever entry set
Manufacturer-approved cylinder lubricant
Filler plates and thick-door extension kits
Boring jig and hole saws
75 millimetre strike and hinge screws
Lock Replacement & Upgrade
What affects the quote
Changes to the door preparation
Adjusting a strike mortise is minor; boring a new hole for a deadbolt, fitting a filler plate over an old mortise pocket or adapting a thick door with extension kits is quoted as its own item.
Smart lock setup
Fitting a keypad or smart deadbolt includes programming codes, pairing to a phone or hub and calibrating the bolt, which is time on top of the mechanical installation and is named in the quote.
Authorization needed from a property manager or landlord
A rental or condominium unit sometimes needs sign-off from a property manager or landlord before a lock is changed, and new keys may need to reach more than one party afterward. Confirming who is authorized and who receives keys is worked out before the new hardware goes in.
What to have ready
- How many keys does the household need, and should copying be restricted?
- Do you own the home, or rent it with the landlord's agreement to change locks?
- Is there a sliding patio door or French door to include?
Lock Replacement & Upgrade: questions
QuestionsHow long does a lock replacement take?
A straightforward like-for-like deadbolt or knob set on a standard door is often a matter of an hour or less including testing. Add time for a reinforced strike, for keying several locks alike and cutting keys, for a smart lock's setup and pairing, and for repairing a split jamb or adapting an older door. When several entrances are done together, the locksmith gives a realistic window before starting so you can plan the day.
Which finishes stand up to salt and winter?
Finish is one of the three categories on the residential hardware label, and it covers exposure to sun, humidity, salt and skin oils. In practice, PVD brass, satin nickel and stainless finishes tolerate a salted driveway well, powder-coated black holds up when it is not chipped, and traditional lacquered brass tends to bloom green where salt reaches it. A storm door or a small overhang helps any finish, and wiping salt off in a thaw helps more.
Do I have to prove I own the home before you change a lock?
The locksmith will ask, and it is a sign of a careful trade. Photo identification with the address, a deed or property tax notice, or a mortgage or insurance document is plenty for an owner. Tenants show a lease and the landlord's consent; landlords show ownership and confirm the tenant will receive keys. It is a short step that protects everyone with a right to that door.
Related services
- Deadbolt InstallationThe front door has a handsome lever and a keyed knob, and that is all.
- Vintage Mortise Lock ServiceThe interior bedroom doors on the second floor have the original mortise latches, and none of them close any more.
- Smart Lock InstallationArthritis has made the small house key hard to grip and turn, especially with gloves on in January.